ZK linear vibrating screen for mining

Use:

ZK linear vibrating screen for mining, linear movement, suitable for coal preparation, coal washing, dressing, power and other industries, the fine grained material, dry and wet sieving, can also be dehydration, stripping and desliming.

The principle of work:

Linear vibrating screen are seat mounted. The utility model is characterized in that the utility model adopts a double shaft vibration exciter, the motor does not participate in the vibration, and the two motors are driven to rotate synchronously with the action, so that the screen body can make periodic reciprocating motion along a straight line direction, thereby achieving the purpose of screening.

Performance characteristics:

1. Processing capacity, screening efficiency is higher.

2. The structure is more simple.

3. The operation is simple, the failure rate is the lowest.

4. Low equipment cost, reduce energy consumption.

Structure introduction:

 ZK series linear vibrating screen is mainly composed of screen box, exciter, supporting device and motor. The screen box is supported by a rubber spring on the support, and the two shafts of the exciter are respectively driven by two asynchronous motors.

1.The screen box for space metal structure of high strength bolt connection, mainly composed of side plates, plus strong plate, reinforcing plate, beam, beam, beam, head out to strengthen the sieve plate etc.. Bearing truss girders, for supporting fastening sieve plate; extend and support head beam device is used to support the entire screen is connected with the side of the box; all parts are made of torsional shear type high strength bolt; plate adopt stainless steel plate, high porosity, good abrasion resistance, as if the slime screen is installed on one. Layer composite filter on the sieve plate, simple and convenient.

2. The exciter is a double eccentric block type vibrator. The exciting force is strong and the amplitude can be adjusted in a certain range. It is mainly composed of a main shaft, bearing, bearing seat, eccentric block, fan, protective cover, vibration exciter spindle supported on two roller bearings, which is arranged on the eccentric block and the counterweight. Two the angle of the exciter eccentric block of sieve vibration direction. The main function of the fan is to promote the flow of air in the protective cover to reduce the working temperature of the bearing.

3. the supporting device adopts rubber damping spring, mainly composed of a gland, upper bearing, rubber spring and the lower supporting seat. On the cover and the upper supporting seat and out of the screen box beam head with bolts connected on the supporting seat and the supporting seat is arranged between the rubber spring and rubber spring has the advantages of long service life, low noise, parking is stable and fast and reliable. The lower supporting seat is fixed on the mounting base, and the inclination angle of the screen surface can be adjusted by increasing or decreasing the gasket on the lower supporting seat.

Installation and commissioning

1. preparation before installation

Before installation should be carefully checked, according to the inventory list of equipment and random accessories are complete, at the same time should check whether the damage caused by the shipment and the loss of random accessories, and promptly notify the manufacturer.

2.installation

1) support installation: the installation support device of bearing and motor frame before the foundation leveling, then adjust and install the bearing and motor frame, and then the rubber spring is installed in the spring.

2) the installation of screen box: sieve box adopts integral hoisting, lifting to the wire rope at the specified location (beam) are not allowed in the direct lifting vibrator, so as to avoid deformation. The screen box is then hung above the supporting position and then slowly lowered to make it located on the spring.

3) motor installation: installation, the horizontal motor needs correction, axial center lines of the output shaft of the electric motor and the vibrator should be coincident or slightly below the exciter shaft center line, but not more than 5mm. After the motor is installed in a predetermined position, the connecting wire is connected with the motor and the electric network, and the rotation direction of the two motors is opposite.

4) check the connecting parts (such as vibration sieve plate, vibration etc.) fixed, lubrication of the transmission part of the motor wiring is correct, and the hand rotation driving part, to see whether normal movement.

5) check the exciter rotation is flexible, moving the coupling to the exciter eccentric block from the equilibrium position, and then suddenly let go, the eccentric block should be several times the swing, if the move or not to move, it should be carefully to find out the reasons and adjust.

6) if the vibration screen from the date of shipment to the shipment for more than half a year, or due to improper storage caused by rust and so on should be removed and cleaned the vibration exciter, before installation and use.

3. the test run of vibrating screen is installed, should be performed for test run, a preliminary examination of the quality of the installation, and make the necessary adjustments.

1) empty sieve test run time shall not be less than 8 hours. During this time, observe whether to start the sieve quickly and smoothly, whether the vibration and stable operation, there is no special noise.

2) screen operation, vibration sieve box should not produce yaw. As a result of yaw, the reason may be too large or spring height on both sides of the rotating shaft is not level, we should make the corresponding adjustment.

3) if there is an abnormal noise or a sharp increase in bearing temperature after driving, stop immediately, check whether the bearing is flexible and the lubrication is good or not.

4) after driving 2 ~ 4H stop check the connection parts are loose, if there is loose, to be fastened and then drive.

5) after the commissioning of the 8h, if there is no fault, the installation works can be checked and accepted.

Operation and maintenance operating points :

1.The operator should check the equipment before work. Check the lubrication condition of the exciter, the tension of the screen, the tightening of bolts and the damage of the sieve surface.

2.A start should follow the process system order: empty parking should be started before the material on the sieve net before parking, parking is prohibited with material feeding to sieve.

3.In a work, to use visual and auditory examination of exciter and screen box work, touch the bearing cover by hand near the parking, check the bearing temperature rise.

4.Screen is high speed equipment, sieve operation inspection personnel to maintain a safe distance.

Technical parameter:

Application:

ZK linear vibrating screen for mining trajectory is linear, for coal preparation, coal washing, mineral processing, power generation and other industries, On the medium and fine materials dry and wet screening, Can also be dewatering, Off medium, desliming operations.

Summary:

Linear vibrating screen are seat type installation, using a biaxial exciter, motor does not participate in vibration, by the two motor with the reverse self-synchronous rotation, so that the screen in a straight line for the cyclical reciprocating motion, so as to achieve the purpose of screening.

Performance characteristics:

1.Large capacity, higher screening efficiency.

2.The structure is more simple.

3.The operation more simple, the lowest failure rate.

4.Equipment using low cost, reduce energy consumption.